need help son got a hold of the remote and now it got a bunch of line going up very fast and you can't see any thing on the menu

Try a hard boot.Turn rear power switch off and on.

__________________

did not work still doing the same thing do you have a loader program and the

need factory default to load to it can't use remote need help

Can use the buttons on receiver.

__________________

I got lines going up and down on my tv screen when i turn the box on, and i also turned the box off and back on again and it still does the same thing lines going thru it up and down, what i am asking you is there a fix for this problem

Here is a link for CW Ultima Loader.

http://www.ftaprofessionals.tv/capti...er-5-02-a.html

Link for Factory file. http://www.ftaprofessionals.tv/capti...er-5-02-a.html

Link for latest fix http://www.ftaprofessionals.tv/capti...10-2009-a.html

Load factory file first then the latest file. Make sure you press STB button on your remote. Patch can be enabled without the remote as well.

Enable Patch without Remote via the front panel.

Put box in standby mode then press OK Button then VOL+ Button, VOL- Button and then box should turn on and patch should be enabled.

__________________

Please don't PM me with fta related questions, ask them in open forums so others can benefit from them too.

how do you set up the sat 110 and 119 i'm new at this need help

Go into Menu, select System Setting
Select System
This is how mine is setup, your's may be different depending on language, TV screen format, etc.
Menu language : English
Audio 1 : English
Audio 2 : English
Close Caption : Off
Channel No. : SID
TV System : NTSC
TV screen format : 4:3
Recall History : Off ( this is a nice feature if you want to enable it. If you do, when you press Recall it will show you a list of the channels you've been watching)
Auto TP : On
Key Update message : Off
Bev&Dishnet Fullname : On
Press Exit when done.

Select OSD

The only option I changed here was the TimeOut. I changed it from 3 sec to 8 sec. This gives you more time between keystrokes when you're entering channel numbers.
Press Exit, Exit.
Select Accessories
Select Setup Wizard
English, Ok
English, Ok
Select your time zone. For EST, select GMT – 5:00. If you're not sure how to set this, look in the front of your phone book. **** Canada has a map of North America that shows the different time zones and the GMT offset. I set mine for GMT – 5:00 (EST) Press the right arrow to turn on SummerTime. (also known as Daylight Savings Time)
Press Ok
Press Ok again.
The antenna setting screen will appear. Scroll right/left to the highest numbered satellite you have.
Scroll down and enter the settings for your setup.
I'm using ******** 119 & 110, so here's the settings I use:
Satellite Name: 17.******** 7 (119W)
Transponder : 12239/H/20000/5/6
LNB Freq. : 11250
LNB Type : Normal For dish pro set to OCS-DP
22 kHz : OFF unless you use one, then set it to ON
Diseqc Number : LNB 1 Note: LNB 1 = Port 1
Legacy SW : OFF
Motorised System : OFF

When you are done, press the Red button on the remote marked Audio. This will start the scan for this satellite.
The prompt “Only FTA channels search?” will appear. Select NO, press Ok.
When the scan is done, the antenna settings screen will re-appear. Scroll to next satellite you have, scroll down and enter the correct settings for this satellite.
Here's the settings I use:
Satellite Name: 23.******** 6,8 (110W)
Transponder : 12224/V/20000/5/6
LNB Freq. : 11250
LNB Type : Normal For dish pro set to OCS-DP
22 kHz : OFF unless you use one, then set it to ON
Diseqc Number : LNB 2 Note: LNB 2 = Port 2
Legacy SW : OFF
Motorised System : OFF
When you are done, press the Red button on the remote marked Audio. This will start the scan for this satellite.
The prompt “Only FTA channels search?” will appear. Select no, press Ok.
When the scan is done, the antenna settings screen will re-appear. Scroll to next satellite you have, scroll down and enter the correct settings for this satellite.
When you're done scanning all your satellites, press Exit, Exit, Exit.
“Sorting SID” will appear, ( if you chose that option).
When the screen comes back up, press F1 000.
“Patch Enable”should appear.
Power off, then on at the back of the box.
Watch TV.

__________________

Please don't PM me with fta related questions, ask them in open forums so others can benefit from them too.

can anyone tell me why i have double chanels on my box and what i do got don't work