![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
ChatBox Sonicview Conaxsat Nanosat Viewsat i-Link DreamboxLimesat Topsat AzBox Satzen X-Factor |
![]() |
![]() |
|
|||||||
| FTA General Discussion FTA Satellite and FTA Receiver issues. |
![]() |
|
|
LinkBack | Thread Tools | Rate Thread |
|
|||
|
This is a new receiver that I want to setup. These are the steps I followed:
I have 2 dishes with 2 LNB each Dish 1 A) LNB 1 set at 91 W B) LNB 2 set at 82W Dish 2 A) LNB set at 119W B) LNB set at 110W I loaded factory CW700S V1.03 file after loaded the bin file V2.38 Went to the installation, antenna Satellite name: NIMIQ 1 (91W) transponder 10964/V/19850/3/4 LNB freq:11250 22khz ffDiseqc:LNB1 motorized system: none hit red button for auto search, see channels displaying in both boxes. Went to the installation, antenna Satellite name: NIMIQ 2 (82W) transponder 12224/V/20000/7/8 LNB freq:11250 22khz ffDiseqc:LNB2 motorized system: none hit red button for auto search, see channels displaying in both boxes. Went to the installation, antenna Satellite name: Echo Star (110W) transponder 12224/V/20000/7/8 LNB freq:11250 22khz ffDiseqc:LNB4 motorized system: none hit red button for auto search, see channels displaying in both boxes. Went to the installation, antenna Satellite name: NIMIQ 2 (119W) transponder 12224/V/20000/7/8 LNB freq:11250 22khz ffDiseqc:LNB3 motorized system: none hit red button for auto search, see channels displaying in both boxes. Try to press F1 000 to enable the patch but nothing happen, the receiver only display the channel number. All channel are scrambled. Please help, thanks again |
|
||||
|
The only way to get your CW700 up and running is through card sharing via the internet.Which requires you to be a paid monthly subscriber.Clicks link below on the setup for C/S.
http://www.ftaprofessionals.tv/capti...ard-share.html http://www.ftaprofessionals.tv/capti...aring-fix.html
__________________
|
|
|||
|
With the Nfusion, do you get the PPV movies for free?
Do I need extra hardware to meke it work( switch, hub etc) or this will be plug and play. Thank you. Last edited by sat11111; 10-17-2009 at 11:18 AM. Reason: extra question |
|
||||
|
I hope you didn't just buy a new CW 700 receiver, if you did try to return it if you can. NFusion comes with dongle already installed so there is no additional hardware required other then a router but that goes for all IKS receivers.PPV's are down on all IKS receivers and it will most likely stay that way unless N3 get's cracked. If you have any more questions don't hesitate to ask.
__________________
Please don't PM me with fta related questions, ask them in open forums so others can benefit from them too. |
![]() |
| Bookmarks |
| Thread Tools | |
| Rate This Thread | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| CaptiveWorks CW700 - Error 020 - No Sats & Channels Fix | Zero Gravity | CaptiveWorks 700 Instructions | 0 | 11-14-2008 07:16 PM |
![]() |
![]() |