|
 |
 |
 |
 |
 |
 |
 |
ChatBox Sonicview Conaxsat Nanosat Viewsat i-Link DreamboxLimesat Topsat AzBox Satzen X-Factor |
 |
 |
12-15-2011, 03:55 AM
|
||||
|
||||
Limesat HD Air - Set Up Guide
To start:
This Receiver ships with with a Plastic film on the Underside of the Receiver, please remove it so that it can ventilate properly. Installing the LS400 QPSK HD Module The Limesat HD Air comes with a Factory Module HD but mpeg2 only. To replace it with the LS400 do as follows: 1) Remove the 5 screws holding the Cover 2) With the same Phillips Screw Driver remove the Securing Screen holding down the Factory HD Module and pull at both ends to remove this Module (Plug is at opposite end of the Securing Screw Hole) 3) Place the LS400 Turbo HD Module of the pins and push the Plug so it is all the way in. Insert Securing Screw and tighten 4) Replace the Cover Setting up the Receiver 1) Plug in Power Cord 2) Plug in Ethernet adapter 3) Plug In Sat Cable 4) Plug in the HDMI Cable 5) Boot up the Receiver 6) Set up Language (English) 7) Insert the USB Stick with the the latest bin, currently the Limesat HD Air v121 bin and click on this Bin 8) Wait till it loads it, do not power off, when done it reboots on it's own. 9) Go to Menu, Configuration, Recovery, Factory Rest 10) Set Up the Time Off Set Daylight Savings ON or OFF 11) Go to A/V turn SPDIF ON or OFF 12) Set up Auto TP, History ON, etc 13) Set up your Sats and Press Red Button to Scan only when the correct Sat is displayed on the to Right corner of the screen. 14) click on Ch 101, if you have Picture, proceed Setting up the Network For Japan Public Service no codes are required. 1) Press Menu 2) Press Configuration 3) Press Network Settings 4) Be certain Connection Mode is set to DHCP and it indicates connected 5) Press Blue Button to enter the Server Screen 6) Turn on Server 9 and 10 7) Press Red Button to Scan Servers 8) 2 Servers should Show Connected 9) Exit, Save 10) Exit, Exit, Exit 11) Click on CH 200 and wait for Picture For Private server use: 1) Menu 2) Configuration 3) Network Settings 4) Set Connection Type to DHCP (by default) 5) Click on Blue Button to enter Server Menu 6) Choose Server 1 to 8 and switch it on, scroll to right to turn on 7) Enter the URL or IP adddress 8) Enter the Port : 9) Enter the Username: 10) Enter the Password: 11) Enter the DES Keys 12) Press Ok to Connect 13) Press Red Button to Save, Exit 14) Ensure Server(s) you want are turned ON 15) Click Red Button Scan servers - should display the number of servers you turned on with wording, Connected 16) Exit, Save settings 17) click on CH 200 wait for Picture
__________________
 |
 |
| Bookmarks |
| Thread Tools | |
| Rate This Thread | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Limesat HD MAX Setup Guide | Ekim | Limesat Instructions | 0 | 09-19-2011 04:42 AM |
| Entering the Limesat Japan Code in the Limesat Japan Public Server Screen | FTA PRO | Limesat Instructions | 0 | 07-17-2011 05:10 PM |
| Limesat How To Setup Guide | FTA PRO | Limesat Instructions | 0 | 05-24-2010 08:08 PM |
| Limesat PVR Ver 1 2010 Guide | FTA PRO | Limesat Instructions | 0 | 05-21-2010 07:50 PM |
 |
 |
