Please healp me i don't have ipconfig in my 360elite..

please try thie linm to reset your receiver. remember factory reset in the menu selection usually will reset must problems. http://www.ftaprofessionals.tv/sonic...files-v82.html

please try this link http://www.ftaprofessionals.tv/sonic...files-v82.html

Take a look at this link as well, it has all the files and info needed for your receiver >>> http://www.ftaprofessionals.tv/sonic...cessfully.html

__________________

Please don't PM me with fta related questions, ask them in open forums so others can benefit from them too.

till nothing in my receiver

also along with the setup FTA PRO had
http://www.ftaprofessionals.tv/sonicview-360-elite-other-files/4894-ihub-how-fix-v82-0-get-ip-config-back-menu-flash-1-4-successfully.html


C/P......
You CANNOT flash a virgin Ihub!
If you do then you will get the dreaded v82 issue that is more time consuming than doing it right the first time.

To flash a virgin Ihub:
You need to connect the Ihub to the reciever
go into IP Config screen
Change Static to DHCP and then press ok on apply
You will now have a DHCP address in the correct range

The default static IP on the Ihub is 192.168.11.X
The 11 is out of most peoples ranges and when you try to flash it
You will corrupt your Ihub

If you have alread corrupted your Ihub
meaning when you turn it on and it doesn't recognize it (no Ip config under installation)
Then you need to fix it using this:

Open up the Wiznet flash config tool
note your Ihub's information

local ip: 192.168.11.2
Gateway: 192.168.11.1

these values will only work with a network that are 192.168.11.X
Since these values don't match my network I changed it to settings that match my network

Local Ip: 192.168.1.102
Gateway: 192.168.1.1

If you don't know your range or gateway then hit the start menu on the bottom of windows
find the run tab
type in cmd.exe
a black DOS window will open
now type in ipconfig
use the information in the window to change the value in your Ihub
after you are done then left click on the setting button on the bottom of the Wiznet config tool
It will tell you processing and then you can research and see that indeed the IP address has been changed

Note the Version is still at *****
Now click on the upload tab again on the bottom of the Wiznet config tool window
Locate the file 1.4 and press "open" to upload the file
After the processing stus window you will see "complete uploading"

Now you can do a search and see if the Version of your Ihub is now correct
It should read Version 1.4


note I have found that using the 1.4 instead of the restore file is fine
It gets the job done and it works


and then use the WIZNET http://www.ftaprofessionals.tv/sonicview-360-premier-other-files/4868-instructions-downloads-ihub-wiz-loader-1-4-firmware.html




load the FTA Fixhttp://www.ftaprofessionals.tv/sonicview-360-elite-fta-fix-files/4824-sonicview-360-elite-dongle-ihub-fix-july-11-2009-a.html

__________________

and do you have the correct setup in settings
should look some thing like this

Below is what most have:
Menu===>Installation then 0000 or 0937 or 2668 or 3570 then antenna setup then side arrow to ECHOSTAR 7=119W.then do the same for ECHOSTAR 8,10=110W,and NIMIQ 1,3=91.0W.
..............EchoStar 7=119W........................ .EchoStar 8,10=110W.
LNB Power................ON....... .................... ...............ON
LNB Type..............Standard.... .................... ..........Standard (Dish Pro change to OCS-DP)
LNB Freq...............11250...... .................... .............11250
22kHz.......................OF F................... .....................OFF
TP Freq.................12239 Or one that closer........................ ..12224 Or one that closer.
search option............ALL......... .................... ..............ALL
DiSEqC 1.0..............Port 1............................. ..........Port 2, (This should match the cable on the switch).
Motor......................OFF .................... ........................OFF
Legacy SW..............NONE.......... .................... ............NONE

NIMIQ 1,3=91.0W
LNB Power...........On
LNB Type............standard (Dish Pro change to OCS-DP)
LNB Freq.............11250
22kHz.................OFf
TP Freq...............12224 or one that is close.
DiSEqC 1.0...........Port 3 or 4 (this should match the cable on the switch).
Motor.................OFF
Legacy SW..........NONE
Good Luck.


and do you have your d!ish properly alighned to rite SAT?

__________________

were i can find Open up the Wiznet flash config tool

its in this link on the bottom of the page http://www.ftaprofessionals.tv/sonicview-360-premier-other-files/4868-instructions-downloads-ihub-wiz-loader-1-4-firmware.html

__________________

when i run Wiznet in the righ read not connected