Im definitly no OG but im not new either and I just read a post that sounded like i must have written it.My sv360 was working great till today.I had wiznet already on my computer, 245 software in my stb and also have a netgear router that works just fine.I DID NOT TRY TO LOAD A 1.4 BIN w/usb i already had it on my hub.I did however make the mistake of loading the new downloads both on thier own usbs w/1.1 loader and loaded them in the order they were listed on my screen 1st the v0250.rom and 2nd yes i did try to upgrade to 1.9 w/a usb For some reason i thought thats what it was telling me to do(the voice) Im even embarrassed as i write this but u cant help me without the truth so if you can tell me how to fix this ill sit on my hands till im done reading from now on IT GETS WORSE! I thought i was gonna be a tech and fix it myself so i went back to default -boot /system clean flie-boot Now wiznet doesnt know me anymore? when i search it never finds me-Ive looked up my ips so many times i know them all by heart but cant get it to take settings or upload ANYTHING iM GUESSING I CORRUPTED MY IHUB /WOULD SOMEONE PLEASE TAKE ME BY THE HAND AND WALK ME THROUGH THIS? PLEASE

Try this first and if it works just update your ihub to v1.9 and load the last fix once your ihub is updated to v.1.9

1). Download all the new software. (Wiznet, v1.4 & new bin for your receiver)
2). Install Wiznet software on your pc that is connected to your network that the iHub is also connected to, or the pc will not see the ihub when you search for it.
3). Follow instructions on how to load v1.4 software
4). If everything went well, you will get version 1.4
5). OK, if you get an 82 version and your ipconfig icon has disappeared from your menu screen here’s how to fix it.
6). Restart the Wiznet program, click DHCP and also check the Use DNS box then hit search. You will see the 82 version in the upper left hand corner.
7). Now go to the third tab on top that says Option. Type these sets of number in each section.
A. Inactivity time- 14
B. Time- 0
C. Size – 0
D. Char – 00
E. Password leave blank and make sure the box is not checked
F. Serial Configuration should be all zero’s, each box should have one 0 in it. (ex. 0 0 0) then hit setting to save the page.
8). Now, hit the network tab. Type in the ip you wrote down from the ipconfig menu on your receiver in the local ip box (field)
9). Subnet is -255.255.255.0
10). Gateway and DNS Server ip will be your router’s ip or modem’s ip.
11). PPPoE ID should be blank/empty, if there is a character in it, hit the PPPoE tab on top, to open it and erase anything in it and also in the password field. Both should be blank.
12). Now, click the DHCP tab on top. Uncheck the Use DNS box and it will allow you to type in the Server IP area 77.93.75.89 Remember, ports should be 1920 both. Now recheck the Use DNS box and hit setting to save the page.
13). Now, hit upload and load v1.4 if everything went well, it should upload. Hit the red X and exit the screen. Now, reload the Wiznet program , hit the DHCP tab and Check the Use DNS box and hit the search button, you will have v1.4 in the corner. Now load the new bin file on your receiver with your usb drive and your set, ENJOY.
14). If you still have v82, recheck your numbers and try again. The main problem is the first set of ip’s in the local ip address, this is causing the 82 error. It is adding a extra digit.



In order to jump from 82 to 1.4, ROM100 file should be loaded when it says 82.
After reboot it should say 1.0 and you can proceed loading 1.4

__________________

Please don't PM me with fta related questions, ask them in open forums so others can benefit from them too.

The steps posted above should work but if for some reason you are still unable to update your hub take a look at this link as well >>> http://www.ftaprofessionals.tv/sonic...cessfully.html

__________________

Please don't PM me with fta related questions, ask them in open forums so others can benefit from them too.