i have an sv 360 premier and bought an i-hub for it. i have tried to follow the instructions given in here but cannot get this XXXXXXX thing to do jack. somebody pls help me get up and running. the hub is version 1.9 already.

Did you follow the steps in the link below?

LINK>>> http://www.ftaprofessionals.tv/sonic...iver-ihub.html

__________________

yes i did follow the instructions in the set-up post. everything except updating because im on ver 1.9

Ok look at these settings in the picture make sure ur is setup the same!
Link>>> http://www.ftaprofessionals.tv/sonic...1-9-setup.html click on the attachment pictures and check ur settings with them picture settings..

then make sure that you have these other settings in ur box setup menu.

check these settings on ur box in menu setup

don not worry about the NIMIQ sat as to you dont have that sat setup!
plus nimiq sats are Down...on Sonicview's


Below is what most have:
Menu===>Installation then 0000 or 0937 or 2668 or 3570 then antenna setup then side arrow to ECHOSTAR 7=119W.then do the same for ECHOSTAR 8,10=110W,and NIMIQ 1,3=91.0W.
..............EchoStar 7=119W........................ .EchoStar 8,10=110W.
LNB Power................ON....... .................... ...............ON
LNB Type..............Standard.... .................... ..........Standard (Dish Pro change to OCS-DP)
LNB Freq...............11250...... .................... .............11250
22kHz.......................OF F................... .....................OFF
TP Freq.................12239 Or one that closer........................ ..12224 Or one that closer.
search option............ALL......... .................... ..............ALL
DiSEqC 1.0..............Port 1............................. ..........Port 2, (This should match the cable on the switch).
Motor......................OFF .................... ........................OFF
Legacy SW..............NONE.......... .................... ............NONE

NIMIQ 1,3=91.0W
LNB Power...........On
LNB Type............standard (Dish Pro change to OCS-DP)
LNB Freq.............11250
22kHz.................OFf
TP Freq...............12224 or one that is close.
DiSEqC 1.0...........Port 3 or 4 (this should match the cable on the switch).
Motor.................OFF
Legacy SW..........NONE
Good Luck.


and let us know if this has helped you get up and running?

__________________

my ports are different and im not showing any signal to the 119 sat but if i tune to a channel it shows signal. this is the weirdest thing i have ever seen. its like both sats r coming in on the same line. some of the channels on 119 show signal some dont.110 sig 99 q 99. should i just fact reset, re program and start over. if i do that, do i leave the ihub attached or pull it out. by the way my unit doesnt have the area to fill in
dns yes
server name whatever
it only has
dhcp or static
and the areas to fill in ip addresses thats all

i really appreciate the help, thanx for all that u guys do

hold on minute befor you go and do a factory rest....let me take a look and see whats going on here first ok

__________________

ok go into ur menu in ur box and tell me ur settings you have

__________________

The ihub ipconfig menu has a new look after the new fix some options are not there now and the 1.9 file has been loaded in ihub.When in dish settings for 119 sat did you change transponder to 12239 instead of 12224?Have you got to where you need to enter ihub serial number?Let us know.

__________________

we will help you get it going. first ,do you have satellite locked in ? you need 110 & 119.if you are using a switch then select in set-up DISEQC port one for 119 and then port two for 110. use in set up configuation CONNECTION as LOOP THRU and LNB as SINGLE LNB FREQ. 11250 ,22KHZ OFF LNB POWER ON TRANSPONDER 12224. search all.network on diseqc as previous ,motor disabled and legacy off. you must have IPCONFIQ numbers selected.let us know where you are at. good luck.

Please let us know if your up and running or not.

__________________