ChatBox Sonicview Conaxsat Nanosat Viewsat i-Link DreamboxLimesat Topsat AzBox Satzen X-Factor

Go Back   FTA Files Community Forums for Satellite Equipment > FTA Files & FTA Instruction & FTA Discussion Section > Viewsat FTA Receivers Support > Viewsat Files & Instructions > Viewsat Ultra FTA Files > Viewsat Ultra Instructions

Reply
 
Thread Tools
  #1 (permalink)  
Old 09-10-2008, 07:34 PM
Super Moderator
 
Posts: 15,587
Thanks: 0
Thanked 38 Times in 26 Posts
Rep Power: 811
Fta Professionals has a reputation beyond reputeFta Professionals has a reputation beyond reputeFta Professionals has a reputation beyond reputeFta Professionals has a reputation beyond reputeFta Professionals has a reputation beyond reputeFta Professionals has a reputation beyond reputeFta Professionals has a reputation beyond reputeFta Professionals has a reputation beyond reputeFta Professionals has a reputation beyond reputeFta Professionals has a reputation beyond reputeFta Professionals has a reputation beyond repute
Default How to fix a dead Viewsat Ultra

Seeing the Knight Rider Lights [----] < Front panel display or only [on]

The most common problems is people turn the power on to soon.

Try loading the Factory File. If it says sending sync request and does start to trasnfer the file, toggle the power switch on the rear of the unit off then on, and it should start to transfer, if not, toggle the switch again.

This is a repair program only! It is a tool used to repair 'dead' boxes. It is not intended to make receivers decrypt anything!

Your VS ULTRA will need the latest fix after it has been restored!

Works on GENUINE ver 1 & 2

Will repair what appeared to be unrepairable 'dead' box...

- Unit will not respond to your remote
- Accidentally loaded the wrong bin
- USB not recognized
- '----' and 'fail'
- Unlocks locked units (codes -0000, 0937, 3570)

This tool has not been tested on clones.

Needed...

Loader2, the PVRloader is just as good
A NULL cable
Install 'mainpg.pgm' via your serial port, your presumed dead unit is now behaving as new! Now get the latest fix and install via your thumb drive.

Do This To Prevent "----"
When updating via usb port "----" can occur.
To prevent the receiver from locking up do this....

Insert usb flash drive..if the "initializing usb port" window pops up and goes away after a few seconds, you can continue on and update.

If the "initializing usb port" window fails to go away on its own.
"DO NOT CONTUNIE TO UPDATE RECEIVER" do this instead.
-shut receiver off using the switch at the back.
-remove usb flash card
-turn receiver back on and try again
Attached Files
File Type: zip VSU_FAIL_FIX.zip (1.01 MB, 75 views)
Reply With Quote
  #2 (permalink)  
Old 09-22-2008, 01:20 PM
Super Moderator
 
Posts: 15,587
Thanks: 0
Thanked 38 Times in 26 Posts
Rep Power: 811
Fta Professionals has a reputation beyond reputeFta Professionals has a reputation beyond reputeFta Professionals has a reputation beyond reputeFta Professionals has a reputation beyond reputeFta Professionals has a reputation beyond reputeFta Professionals has a reputation beyond reputeFta Professionals has a reputation beyond reputeFta Professionals has a reputation beyond reputeFta Professionals has a reputation beyond reputeFta Professionals has a reputation beyond reputeFta Professionals has a reputation beyond repute
Default The fixing consists of replacing the TSOP.

This is from a repairman who has fixed many units for dealers in Miami, FL.

The fixing consists of replacing the TSOP.

Iím sure some of you already know about this fix, but Iím also sure a lot of others have no idea. This is the same fix the VS company is going to do for you. Just buy your own TSOP and do it your self. Or have someone else do it for you for a lot less.

If you have no skills on soldering, I wonít recommend you doing it yourself. You can mess up the board while doing this.

You will need a blower - and itís not for your hair. You will need it for removing the TSOP. You also need a magnifying glass and very very fine soldering tip. The blower is NOT A REGULAR BLOWER. For example I have an ATTEN 850A. Maybe you can find something cheaper similar to the one I have. Especially if all you are going to do is one box. In my case I need it something a little more professional because I do this all the time.

The TSOP is the 48pin chip SST 39vf1601, next to the CPU, and on the Ultra is a 39vf3201.

Now you get the blower and set it to 280 degrees - no higher because you can damage the Board and the TSOP. Then you get yourself a pair of tweezers to help you remove the chip once itís hot enough. Once you have the TSOP removed, you need to remove the extra resin left on the board with very very fine soldering TIP. Once you have the board clean of the extra rosin solder you are ready to put in the new TSOP.

To solder the chip you need to align all 48 pins before you start to solder. Now you are going to solder on one side ONLY and only 2 or 3 pins. Because like that you can go back to the other side of the chip and align another 2 or 3 pins so you can get a straight fit. Once you have 2 pins on one corner and 2 across on the opposite corner, you are ready to start soldering your new TSOP. With a very fine tip you are going to touch all the pins one by one very very carefully so they donít get stuck together in the middle. This is the part thatís a pain in the rear. You need very steady hands for this part of the job and you also will need the magnifying glass.

Believe me, I have fixed hundreds of dead units here in Miami for dealers and this is what needs to be done.

Also units that are stuck on "- - - -" and you canít fix it no matter what you do by flashing it. They will also need the TSOP replaced.

There is a Chinese program that can fix some of the units stuck on the ď- - - - ď, but it won't fix all of them.

Do this at your own risk!

If you are not sure you can do it, then definitely get some one else who knows how to do this type of work.
Reply With Quote
Reply

Thread Tools



All times are GMT -6. The time now is 05:21 AM.
Powered by vBulletin® Version 3.7.3
Copyright ©2000 - 2015, Jelsoft Enterprises Ltd.
Content Relevant URLs by vBSEO 3.2.0
©2008 FTA Fire FTA Forums offers FTA Satellite support and FTA Files FTA Bins for all free to air satellite receivers.
FTA FILES